Parameters

The Mercedes-Benz B-Class has 138 parameters.

● Confirmed◆ In testing○ Supported× Not supported

Battery

Control module voltage `VPWR`SAE J1979Confirmed

Power input to the OBD control module. VPWR is normally battery voltage, less any voltage drop in the circuit between the battery and the control module.

Pelican can show this parameter as the starter battery voltage.

Service 01PID 42
Module7E0 → 7E8
Every10 s

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val}{1000}$
Range: 0 to 65.535 V
Unit: V

Confirmed for 2011, 2017. Supported for 2013.

Climate

Ambient air temperature `AAT`SAE J1979Confirmed

Service 01PID 46
Module7E0 → 7E8
Every15 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011, 2017. Supported for 2013.

Clocks

Time since engine start `RUNTM`SAE J1979Confirmed

Increments while the engine is running. Freezes if the engine stalls. Resets to zero during every control module power-up and when entering the key-on, engine off position. Limited to 65,535 seconds and will not wrap around to zero.

Service 01PID 1F
Module7E0 → 7E8
Every1 s

Bits 0 to 15 of the reply, 16 bits.

Formula: $val$
Range: 0 to 65535 s
Unit: s

Confirmed for 2011, 2017. Supported for 2013.

Control Pedals

Accelerator pedal position D `APP_D`SAE J1979Confirmed

Service 01PID 49
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011. Supported for 2013.

Accelerator pedal position E `APP_E`SAE J1979Confirmed

Service 01PID 4A
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011.

DTCs

Distance traveled since diagnostic trouble codes cleared `CLR_DIST`SAE J1979Confirmed

Distance accumulated since DTCs were cleared (via an external test equipment or possibly, a battery disconnect). This parameter is not associated with any particular DTC. It is simply an indication for inspection/maintenance, of the last time an external test equipment was used to clear DTCs. If greater than 65,535 km have occurred, will remain at 65,535 km and not wrap to zero.

Pelican can show this parameter as the distance since trouble codes were cleared.

Service 01PID 31
Module7E0 → 7E8
Every15 s

Bits 0 to 15 of the reply, 16 bits.

Formula: $val$
Range: 0 to 65535 km
Unit: km

Confirmed for 2011, 2017. Supported for 2013.

Distance traveled while MIL was activated `MIL_DIST`SAE J1979Confirmed

Resets to zero when MIL changes from deactivated to activated, if diagnostic information is cleared, or if at least 40 warm-up cycles occur without MIL being activated.

Service 01PID 21
Module7E0 → 7E8
Every5 s

Bits 0 to 15 of the reply, 16 bits.

Formula: $val$
Range: 0 to 65535 km
Unit: km

Confirmed for 2011, 2017. Supported for 2013.

Malfunction indicator lamp `MIL`SAE J1979Confirmed

The MIL status is OFF during key-on, engine-off bulb check unless MIL has also been commanded ON for a detected malfunction. The status reflects whether there are confirmed DTC(s) stored that are illuminating the MIL. It should not reflect the status of the MIL, which could be on for a function check, flashing I/M readiness or flashing for misfire.

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 0 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Off or on

Confirmed for 2011, 2017. Supported for 2013.

Number of DTCs stored in this ECU `DTC_CNT`SAE J1979Confirmed

Number of confirmed emission-related DTCs stored in the ECU available for display using Service $03.

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bits 1 to 7 of the reply, 7 bits.

Formula: $val$
Range: 0 to 127
Unit: Number

Confirmed for 2011, 2017. Supported for 2013.

Number of warm-ups since diagnostic trouble codes cleared `WARM_UPS`SAE J1979Confirmed

Number of OBD warm-up cycles since all DTCs were cleared (via an external test equipment or possibly, a battery disconnect). A warm-up is defined in the OBD regulations to be sufficient vehicle operation such that coolant temperature rises by at least 22°C (40°F) from engine starting and reaches a minimum temperature of 70°C (160°F) (60°C (140°F) for diesels). This PID is not associated with any particular DTC. It is simply an indication for inspection/maintenance, of the last time an external test equipment was used to clear DTCs. If greater than 255 warm-ups have occurred, this parameter will remain at 255 and not wrap to zero.

Service 01PID 30
Module7E0 → 7E8
Every60 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255
Unit: Number

Confirmed for 2011, 2017. Supported for 2013.

Time run by the engine while MIL was activated `MIL_TIME`SAE J1979Confirmed

Resets to zero when MIL changes from deactivated to activated, if diagnostic information is cleared, or if at least 40 warm-up cycles occur without MIL being activated.

Service 01PID 4D
Module7E0 → 7E8
Every60 s

Bits 0 to 15 of the reply, 16 bits.

Formula: $val$
Range: 0 to 65535 min
Unit: min

Confirmed for 2011.

Status

A/C system refrigerant monitoring `ACRF_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 19 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

A/C system refrigerant monitoring completed `ACRFCMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 27 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

A/C system refrigerant monitoring ready `ACRF_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 27 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Catalyst monitoring `CAT_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 23 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Catalyst monitoring completed `CAT_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 31 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Catalyst monitoring ready `CAT_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 31 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Comprehensive component monitoring completed `CCM_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 9 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Comprehensive component monitoring ready `CCM_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 9 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

EGR system monitoring `EGR_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 16 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

EGR system monitoring completed `EGR_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 24 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

EGR system monitoring ready `EGR_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 24 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Evaporative system monitoring `EVAP_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 21 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Evaporative system monitoring completed `EVAPCMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 29 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Evaporative system monitoring ready `EVAP_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 29 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Fuel system monitoring completed `FUEL_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 10 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Fuel system monitoring ready `FUEL_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 10 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Heated catalyst monitoring `HCAT_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 22 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Heated catalyst monitoring completed `HCATCMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 30 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Heated catalyst monitoring ready `HCAT_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 30 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Misfire monitoring completed `MIS_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 11 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Misfire monitoring ready `MIS_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 11 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Oxygen sensor heater monitoring `HTR_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 17 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Oxygen sensor heater monitoring completed `HTR_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 25 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Oxygen sensor heater monitoring ready `HTR_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 25 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Oxygen sensor monitoring `O2S_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 18 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Oxygen sensor monitoring completed `O2S_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 26 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Oxygen sensor monitoring ready `O2S_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 26 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Secondary air system monitoring `AIR_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 20 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Secondary air system monitoring completed `AIR_CMPL`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 28 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2017. Supported for 2013.

Secondary air system monitoring ready `AIR_RDY`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 28 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Yes or no

Confirmed for 2011, 2017. Supported for 2013.

Support

A/C system refrigerant monitoring supported `ACRF_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 19 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Catalyst monitoring supported `CAT_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 23 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Comprehensive component monitoring enabled `CCM_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 13 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Comprehensive component monitoring supported `CCM_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 13 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Compression ignition monitoring supported `CIM_SUP`SAE J1979Confirmed

Indicates support of spark ignition or compression ignition monitors.

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 12 of the reply.

Unit: Named states

States
Raw value	State	Meaning
`0`	`SPARK`	Spark ignition monitors supported
`1`	`COMPRESSION`	Compression ignition monitors supported

Confirmed for 2011, 2017. Supported for 2013.

Compression ignition monitoring supported `CIM_SUP_FLAG`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 12 of the reply.

Unit: Named states

States
Raw value	State	Meaning
`0`	`SPARK`	Spark ignition monitors supported
`1`	`COMPRESSION`	Compression ignition monitors supported

Confirmed for 2017. Supported for 2013.

EGR system monitoring supported `EGR_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 16 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Evaporative system monitoring supported `EVAP_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 21 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Fuel system monitoring enabled `FUEL_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 14 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Fuel system monitoring supported `FUEL_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 14 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Heated catalyst monitoring supported `HCAT_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 22 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Misfire monitoring enabled `MIS_ENA`SAE J1979Confirmed

Service 01PID 41
Module7E0 → 7E8
Every1 s

Bit 15 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2017. Supported for 2013.

Misfire monitoring supported `MIS_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 15 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Oxygen sensor heater monitoring supported `HTR_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 17 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Oxygen sensor monitoring supported `O2S_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 18 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Secondary air system monitoring supported `AIR_SUP`SAE J1979Confirmed

Service 01PID 01
Module7E0 → 7E8
Every10 s

Bit 20 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011, 2017. Supported for 2013.

Engine

Absolute load value `LOAD_ABS`SAE J1979Confirmed

Pelican can show this parameter as the absolute engine load.

Service 01PID 43
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 25700 %
Unit: %

Confirmed for 2017. Supported for 2013.

Air flow rate from mass air flow sensor `MAF`SAE J1979Confirmed

Pelican can show this parameter as the mass air flow.

Service 01PID 10
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val}{100}$
Range: 0 to 655.35 g/s
Unit: g/s

Confirmed for 2011.

Barometric pressure `BARO`SAE J1979Confirmed

Normally obtained from one of a dedicated barometric sensor, a MAP sensor at key-on and during certain modes of driving, or inferred from a MAF sensor and other inputs during certain modes of driving. The control module reports BARO from whatever source it is derived from.

Service 01PID 33
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255 kPa
Unit: kPa

Confirmed for 2011, 2017. Supported for 2013.

Boost air temperature `BCLASS_BOOST_AIR_T`

Service 22DID 0163
Module7E0 → 7E8
Every5 s
Testing

Bits 48 to 63 of the reply, 16 bits.

Formula: $\frac{val}{10} - 273.1$
Range: -273 to 6280 °C
Unit: °C

In testing for 2005 to 2026.

Boost pressure `BCLASS_BOOST_P`

Service 22DID 0163
Module7E0 → 7E8
Every5 s
Testing

Bits 120 to 135 of the reply, 16 bits. The value is signed.

Formula: $val$
Range: -32768 to 32767
Unit: Raw value

In testing for 2005 to 2026.

Boost pressure sensor A `BP_A_ACT`SAE J1979Confirmed

Actual turbocharger/supercharger A boost pressure.

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bits 24 to 39 of the reply, 16 bits.

Formula: $\frac{val}{32}$
Range: 0 to 2047.96875 kPa
Unit: kPa

Confirmed for 2011.

Boost pressure sensor B `BP_B_ACT`SAE J1979Confirmed

Actual turbocharger/supercharger B boost pressure.

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bits 56 to 71 of the reply, 16 bits.

Formula: $\frac{val}{32}$
Range: 0 to 2047.96875 kPa
Unit: kPa

Confirmed for 2011.

Calculated engine load `LOAD_PCT`SAE J1979Confirmed

Represents the amount of work the engine is doing. Expected to reach 100% at wide open throttle/wide open pedal at any altitude, temperature or rpm for both naturally aspirated and boosted engines. If engine load is limited for powertrain protection e.g. engine/turbocharger protection, this value may not reach 100%. For hybrid vehicles, indicates the torque produced only by the internal combustion engine, not the torque being delivered by the entire powertrain. For electric vehicles, the meaning of this parameter is undefined.

Pelican can show this parameter as the engine load.

Service 01PID 04
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011, 2017. Supported for 2013.

Catalyst temperature bank 1, sensor 1 `CATEMP11`SAE J1979Confirmed

Service 01PID 3C
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val}{10} - 40$
Range: -40 to 6513.5 °C
Unit: °C

Confirmed for 2011, 2017. Supported for 2013.

Commanded boost pressure A `BP_A_CMD`SAE J1979Confirmed

Turbocharger/supercharger A commanded boost pressure.

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bits 8 to 23 of the reply, 16 bits.

Formula: $\frac{val}{32}$
Range: 0 to 2047.96875 kPa
Unit: kPa

Confirmed for 2011.

Commanded boost pressure B `BP_B_CMD`SAE J1979Confirmed

Turbocharger/supercharger B commanded boost pressure.

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bits 40 to 55 of the reply, 16 bits.

Formula: $\frac{val}{32}$
Range: 0 to 2047.96875 kPa
Unit: kPa

Confirmed for 2011.

Commanded equivalence ratio `EQ_RAT`SAE J1979Confirmed

Commanded fuel/air equivalence ratio (lambda): actual A/F ratio over stoichiometric A/F ratio, so above 1 is lean and below 1 is rich. Multiply by the fuel's stoichiometric A/F ratio for the commanded A/F ratio (gasoline: 14.64 x 0.95 = 13.9). Systems with conventional oxygen sensors show the commanded value in open loop and 1.000 in closed loop; systems with wide-range (linear) sensors show it in both. On engines whose banks are controlled independently, this is bank 1.

Pelican can show this parameter as the commanded lambda.

Service 01PID 44
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val}{32768}$
Range: 0 to 1.99
Unit: Number

Confirmed for 2017. Supported for 2013.

Commanded evaporative purge `EVAP_PCT`SAE J1979Confirmed

Service 01PID 2E
Module7E0 → 7E8
Every1 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2017. Supported for 2013.

Commanded Throttle Actuator A Control `TAC_A_CMD`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bits 8 to 15 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011.

Commanded Throttle Actuator B Control `TAC_B_CMD`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bits 24 to 31 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011.

Commanded throttle actuator control `TAC_PCT`SAE J1979Confirmed

Service 01PID 4C
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011, 2017.

Diesel particulate filter differential pressure `BCLASS_DPF_DIFF_P`

Service 22DID 0168
Module7E0 → 7E8
Every1 s
Testing

Bits 320 to 335 of the reply, 16 bits. The value is signed.

Formula: $val$
Range: -32768 to 32767
Unit: Raw value

In testing for 2005 to 2026.

Engine coolant temperature `ECT`SAE J1979Confirmed

Your engine temperature must operate within a certain temperature range to operate efficiently and safely. If it runs too hot, then your engine could be permanently damaged. If it runs too cold, then your engine will use more fuel than necessary.

Pelican can show this parameter as the engine coolant temperature.

Service 01PID 05
Module7E0 → 7E8
Every500 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011, 2017. Supported for 2013.

Engine coolant temperature 1 `ECT_1`SAE J1979Confirmed

Service 01PID 67
Module7E0 → 7E8
Every1 s

Bits 8 to 15 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Engine coolant temperature 2 `ECT_2`SAE J1979Confirmed

Service 01PID 67
Module7E0 → 7E8
Every1 s

Bits 16 to 23 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Engine oil temperature `BCLASS_EOT`

Service 22DID 2095
Module7E0 → 7E8
Every5 s
Testing

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 27}{20} - 54$
Range: -54 to 290 °F
Unit: °F

In testing for 2005 to 2026.

Engine oil temperature `EOT`SAE J1979Confirmed

Pelican can show this parameter as the engine oil temperature.

Service 01PID 5C
Module7E0 → 7E8
Every1 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Engine RPM `RPM`SAE J1979Confirmed

Pelican can show this parameter as the engine speed.

Service 01PID 0C
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val}{4}$
Range: 0 to 16383.75 rpm
Unit: rpm

Confirmed for 2011, 2017. Supported for 2013.

Exhaust back pressure `BCLASS_EXH_BACK_P`

Service 22DID 0168
Module7E0 → 7E8
Every1 s
Testing

Bits 0 to 15 of the reply, 16 bits. The value is signed.

Formula: $val$
Range: -32768 to 32767
Unit: Raw value

In testing for 2005 to 2026.

Fuel rail pressure `FRP`SAE J1979Confirmed

Fuel rail pressure at the engine when the reading is referenced to atmosphere (gage pressure).

Service 01PID 23
Module7E0 → 7E8
Every250 ms

Bits 0 to 15 of the reply, 16 bits.

Formula: $val \times 10$
Range: 0 to 655350 kPa
Unit: kPa

Confirmed for 2011, 2017. Supported for 2013.

Intake air temperature `IAT`SAE J1979Confirmed

Service 01PID 0F
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011, 2017. Supported for 2013.

Intake air temperature, bank 1, sensor 1 `IAT_11`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bits 8 to 15 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Intake manifold absolute pressure `MAP`SAE J1979Confirmed

Service 01PID 0B
Module7E0 → 7E8
Every1 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255 kPa
Unit: kPa

Confirmed for 2017. Supported for 2011, 2013.

Long term fuel trim (bank 1) `LONGFT1`SAE J1979Confirmed

Service 01PID 07
Module7E0 → 7E8
Every1 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{128} - 100$
Range: -100 to 99.2 %
Unit: %

Confirmed for 2017. Supported for 2013.

Long term secondary O2 sensor fuel trim (bank 1) `LGSO2FT1`SAE J1979Confirmed

Service 01PID 56
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{128} - 100$
Range: -100 to 99.22 %
Unit: %

Confirmed for 2017.

Radiator temperature `BCLASS_RADIATOR_T`

Service 22DID 2017
Module7E0 → 7E8
Every5 s
Testing

Bits 0 to 15 of the reply, 16 bits.

Formula: $\frac{val \times 27}{32} + 32$
Range: 0 to 55327 °F
Unit: °F

In testing for 2005 to 2026.

Relative Throttle A Position `TP_A_REL`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bits 16 to 23 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011.

Relative Throttle B Position `TP_B_REL`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bits 32 to 39 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011.

Short term fuel trim (bank 1) `SHRTFT1`SAE J1979Confirmed

Correction being used by the closed-loop fuel algorithm.

Pelican can show this parameter as the short term fuel trim.

Service 01PID 06
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{128} - 100$
Range: -100 to 99.2 %
Unit: %

Confirmed for 2017. Supported for 2013.

Timing advance `SPARKADV`SAE J1979Confirmed

Ignition timing spark advance for the first cylinder. Measured in degrees before dead center. Minus is degrees before dead center, positive is degrees after.

Service 01PID 0E
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val}{2} - 64$
Range: -64 to 63.5 °
Unit: °

Confirmed for 2017. Supported for 2013.

Type of fuel currently being used by the vehicle `FUEL_TYP`SAE J1979Confirmed

Service 01PID 51
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Unit: Named states

States
Raw value	State	Meaning
`1`	`GAS`	Gasoline/petrol
`2`	`METH`	Methanol
`3`	`ETH`	Ethanol
`4`	`DSL`	Diesel
`5`	`LPG`	Liquefied petroleum gas
`6`	`CNG`	Compressed natural gas
`7`	`PROP`	Propane
`8`	`ELEC`	Battery/electric
`9`	`BI_GAS`	Bi-fuel vehicle using gasoline/petrol
`10`	`BI_METH`	Bi-fuel vehicle using methanol
`11`	`BI_ETH`	Bi-fuel vehicle using ethanol
`12`	`BI_LPG`	Bi-fuel vehicle using LPG
`13`	`BI_CNG`	Bi-fuel vehicle using CNG
`14`	`BI_PROP`	Bi-fuel vehicle using propane
`15`	`BI_ELEC`	Bi-fuel vehicle using battery
`16`	`BI_MIX`	Bi-fuel vehicle using battery and combustion engine for propulsion
`17`	`HYB_GAS`	Hybrid vehicle using gasoline engine for propulsion
`18`	`HYB_ETH`	Hybrid vehicle using gasoline engine on ethanol for propulsion
`19`	`HYB_DSL`	Hybrid vehicle using diesel engine for propulsion
`20`	`HYB_ELEC`	Hybrid vehicle using battery for propulsion
`21`	`HYB_MIX`	Hybrid vehicle using battery and combustion engine for propulsion
`22`	`HYB_REG`	Hybrid vehicle in regeneration mode
`23`	`BI_DSL`	Bi-fuel vehicle using diesel
`24`	`BI_NG`	Bi-fuel vehicle using natural gas
`25`	`BI_DSL`	Bi-fuel vehicle using diesel
`26`	`NG`	Natural gas
`27`	`DSL_CNG`	Dual fuel vehicle using diesel and CNG
`28`	`DSL_LNG`	Dual fuel vehicle using diesel and LNG
`29`	`FC_H2`	Fuel cell utilizing hydrogen
`30`	`HICE_HHO`	Hydrogen Internal Combustion Engine
`31`	`KERO`	Kerosene
`32`	`HFO`	Heavy Fuel Oil

Confirmed for 2017.

Internal

Boost pressure A control status supported `BP_A_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 5 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Boost pressure A supported `BP_A_ACT_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 6 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Boost pressure B control status supported `BP_B_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 2 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Boost pressure B supported `BP_B_ACT_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 3 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Commanded boost pressure A supported `BP_A_CMD_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 7 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Commanded boost pressure B supported `BP_B_CMD_SUP`SAE J1979Confirmed

Service 01PID 70
Module7E0 → 7E8
Every250 ms

Bit 4 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Commanded Throttle Actuator A Control supported? `CTAC_A_SUP`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bit 7 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Commanded Throttle Actuator B Control supported? `CTAC_B_SUP`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bit 5 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 1, Sensor 1 supported `IAT_11_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 7 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 1, Sensor 1 supported `IAT_21_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 4 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 1, Sensor 2 supported `IAT_12_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 6 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 1, Sensor 3 supported `IAT_13_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 5 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 2, Sensor 2 supported `IAT_22_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 3 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

IAT Bank 2, Sensor 3 supported `IAT_23_SUP`SAE J1979Confirmed

Service 01PID 68
Module7E0 → 7E8
Every250 ms

Bit 2 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Is ECT sensor 1 supported? `ECT_1_SUP`SAE J1979Confirmed

Service 01PID 67
Module7E0 → 7E8
Every1 s

Bit 7 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Number

Confirmed for 2011.

Is ECT sensor 2 supported? `ECT_2_SUP`SAE J1979Confirmed

Service 01PID 67
Module7E0 → 7E8
Every1 s

Bit 6 of the reply.

Formula: $val$
Range: 0 to 1
Unit: Number

Confirmed for 2011.

Relative Throttle A Position data supported? `RTP_A_SUP`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bit 6 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Relative Throttle B Position data supported? `RTP_B_SUP`SAE J1979Confirmed

Service 01PID 6C
Module7E0 → 7E8
Every250 ms

Bit 4 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Fuel

Commanded Fuel Rail Pressure A `FRP_A_CMD`SAE J1979Confirmed

Displays commanded fuel rail pressure when the reading is referenced to atmosphere (gage pressure)

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 8 to 23 of the reply, 16 bits.

Formula: $val \times 10$
Range: 0 to 655350 kPa
Unit: kPa

Confirmed for 2011.

Commanded Fuel Rail Pressure B `FRP_B_CMD`SAE J1979Confirmed

Displays commanded fuel rail pressure when the reading is referenced to atmosphere (gage pressure)

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 48 to 63 of the reply, 16 bits.

Formula: $val \times 10$
Range: 0 to 655350 kPa
Unit: kPa

Confirmed for 2011.

Fuel rail pressure `BCLASS_FUEL_RAIL_P`

Service 22DID 2071
Module7E0 → 7E8
Every1 s
Testing

Bits 0 to 15 of the reply, 16 bits.

Formula: $val \times 0.4998701$
Range: 0 to 32758 kPa
Unit: kPa

In testing for 2005 to 2026.

Fuel Rail Pressure A `FRP_A`SAE J1979Confirmed

Displays fuel rail pressure when the reading is referenced to atmosphere (gage pressure).

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 24 to 39 of the reply, 16 bits.

Formula: $val \times 10$
Range: 0 to 655350 kPa
Unit: kPa

Confirmed for 2011.

Fuel Rail Pressure B `FRP_B`SAE J1979Confirmed

Displays fuel rail pressure when the reading is referenced to atmosphere (gage pressure).

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 64 to 79 of the reply, 16 bits.

Formula: $val \times 10$
Range: 0 to 655350 kPa
Unit: kPa

Confirmed for 2011.

Fuel Rail Temperature A `FRT_A`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 40 to 47 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Fuel Rail Temperature B `FRT_B`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bits 80 to 87 of the reply, 8 bits.

Formula: $val - 40$
Range: -40 to 215 °C
Unit: °C

Confirmed for 2011.

Fuel system 1 status `FUELSYS1`SAE J1979Confirmed

Service 01PID 03
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Unit: Named states

States
Raw value	State	Meaning
`0`	`OFF`	No status reported: this fuel system is not running or not present, e.g. the engine is off
`1`	`OL`	Open loop - has not yet satisfied conditions to go closed loop
`2`	`CL`	Closed loop - using oxygen sensor(s) as feedback for fuel control
`4`	`OL-Drive`	Open loop due to driving conditions (e.g. power enrichment, deceleration enleanment)
`8`	`OL-Fault`	Open loop - due to detected system fault
`16`	`CL-Fault`	Closed loop, but fault with at least one oxygen sensor - may be using single oxygen sensor for fuel control
`32`	`OL B2`	Open loop - has not yet satisfied conditions to go closed loop (Bank 2)
`64`	`OL-Drive B2`	Open loop due to driving conditions (Bank 2) (e.g. power enrichment, deceleration enleanment, cylinder deactivation)
`68`	`OL-Drive B1+B2`	Open loop due to driving conditions on bank 1 and bank 2 (e.g. power enrichment, deceleration enleanment, cylinder deactivation)
`128`	`OL-Fault B2`	Open loop - due to detected system fault (Bank 2)

Confirmed for 2017. Supported for 2013.

Fuel system 2 status `FUELSYS2`SAE J1979Confirmed

Service 01PID 03
Module7E0 → 7E8
Every250 ms

Bits 8 to 15 of the reply, 8 bits.

Unit: Named states

States
Raw value	State	Meaning
`0`	`OFF`	No status reported: this fuel system is not running or not present, e.g. the engine is off
`1`	`OL`	Open loop - has not yet satisfied conditions to go closed loop
`2`	`CL`	Closed loop - using oxygen sensor(s) as feedback for fuel control
`4`	`OL-Drive`	Open loop due to driving conditions (e.g. power enrichment, deceleration enleanment)
`8`	`OL-Fault`	Open loop - due to detected system fault
`16`	`CL-Fault`	Closed loop, but fault with at least one oxygen sensor - may be using single oxygen sensor for fuel control
`32`	`OL B2`	Open loop - has not yet satisfied conditions to go closed loop (Bank 2)
`64`	`OL-Drive B2`	Open loop due to driving conditions (Bank 2) (e.g. power enrichment, deceleration enleanment, cylinder deactivation)
`68`	`OL-Drive B1+B2`	Open loop due to driving conditions on bank 1 and bank 2 (e.g. power enrichment, deceleration enleanment, cylinder deactivation)
`128`	`OL-Fault B2`	Open loop - due to detected system fault (Bank 2)

Confirmed for 2017. Supported for 2013.

Fuel tank level `BCLASS_FUEL_TANK_LEVEL`

Service 22DID 2030
Module7E0 → 7E8
Every1 s
Testing

Bits 0 to 15 of the reply, 16 bits.

Formula: $val \times 0.099934824$
Range: 0 to 6549 L
Unit: L

In testing for 2005 to 2026.

Fuel tank level `FLI`SAE J1979Confirmed

Pelican can show this parameter as the fuel tank level.

Service 01PID 2F
Module7E0 → 7E8
Every1 s

Bits 0 to 7 of the reply, 8 bits.

Formula: $\frac{val \times 100}{255}$
Range: 0 to 100 %
Unit: %

Confirmed for 2011, 2017.

Fuel temperature `BCLASS_FUEL_T`

Service 22DID 016F
Module7E0 → 7E8
Every5 s
Testing

Bits 128 to 143 of the reply, 16 bits.

Formula: $\frac{val}{10} - 273$
Range: -273 to 6280 °C
Unit: °C

In testing for 2005 to 2026.

Internal

Commanded Fuel Rail Pressure A data supported? `FRP_A_CMD_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 7 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Commanded Fuel Rail Pressure B data supported? `FRP_B_CMD_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 4 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Fuel Rail Pressure A data supported? `FRP_A_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 6 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Fuel Rail Pressure B data supported? `FRP_B_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 3 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Fuel Temperature A data supported? `FRT_A_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 5 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Fuel Temperature B data supported? `FRT_B_SUP`SAE J1979Confirmed

Service 01PID 6D
Module7E0 → 7E8
Every250 ms

Bit 2 of the reply.

Formula: $val$
Range: 0 to 1
Unit: No or yes

Confirmed for 2011.

Movement

Vehicle speed `VSS`SAE J1979Confirmed

Pelican can show this parameter as the speed.

Service 01PID 0D
Module7E0 → 7E8
Every250 ms

Bits 0 to 7 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255 km/h
Unit: km/h

Confirmed for 2011. Supported for 2013, 2017.

OBD

OBD requirements to which vehicle is designed `OBDSUP`SAE J1979Confirmed

Service 01PID 1C
Module7E0 → 7E8
Every3600 s

Bits 0 to 7 of the reply, 8 bits.

Unit: Named states

States
Raw value	State	Meaning
`1`	`OBD II`	OBD II (California ARB)
`2`	`OBD`	OBD (Federal EPA)
`3`	`OBD & OBD II`
`4`	`OBD I`
`5`	`NO OBD`	Not OBD compliant
`6`	`EOBD`
`7`	`EOBD & OBD II`
`8`	`EOBD & OBD`
`9`	`EOBD, OBD, OBD II`
`10`	`JOBD`
`11`	`JOBD & OBD II`
`12`	`JOBD & EOBD`
`13`	`JOBD, EOBD, OBD II`
`14`	`EURO IV B1`	Heavy duty vehicles (EURO IV) B1
`15`	`EURO V B2`	Heavy duty vehicles (EURO V) B2
`16`	`EURO C`	Heavy duty vehicles (EURO EEC) C (gas engines)
`17`	`EMD`	Engine manufacturer diagnostics (EMD)
`18`	`EMD+`	Engine Manufacturer Diagnostics Enhanced (EMD+)
`19`	`HD OBD-C`	Heavy Duty On-Board Diagnostics (Child/Partial)
`20`	`HD OBD`	Heavy Duty On-Board Diagnostics
`21`	`WWH OBD`	World Wide Harmonized OBD
`23`	`HD EOBD-I`	Heavy Duty Euro OBD Stage I without NOx Control
`24`	`HD EOBD-I N`	Heavy Duty Euro OBD Stage I with NOx Control
`25`	`HD EOBD-II`	Heavy Duty Euro OBD Stage II without NOx Control
`26`	`HD EOBD-II N`	Heavy Duty Euro OBD Stage II with NOx Control
`27`	`HD-ZEV`	Heavy Duty ZEV
`28`	`OBDBr-1`	Brazil OBD Phase 1
`29`	`OBDBr-2`	Brazil OBD Phase 2 and Phase 2+
`30`	`KOBD`	Korean OBD
`31`	`IOBD-I-BS4`	India BS4 OBD I
`32`	`IOBD-II-BS4`	India BS4 OBD II
`33`	`HD EOBD-VI`	Euro VI
`34`	`OBD, OBD II and HD OBD`
`35`	`OBDBr-3`	Brazil OBD Phase 3
`36`	`MC EOBD-I`	Motorcycle, Euro OBD-I
`37`	`MC EOBD-II`	Motorcycle, Euro OBD-II
`38`	`MC COBD-I`	Motorcycle, China OBD-I
`39`	`MC TOBD-I`	Motorcycle, Taiwan OBD-I
`40`	`MC JOBD-I`	Motorcycle, Japan OBD-I
`41`	`CN-OBD-6`	China Nationwide Stage 6
`42`	`OBDBr-P7`	Brazil OBD Phase 7
`43`	`CN-HDOBD-VI`	China Heavy Duty VI
`44`	`IOBD-I-BS6`	India BS6 OBD I
`45`	`IOBD-II-BS6`	India BS6 OBD II
`46`	`IHDOBD-BSVI`	India BSVI HD OBD
`47`	`OBDBr-P8`	Brazil OBD Phase 8
`48`	`HD-JOBD-II`	Japan Heavy Duty OBD-II
`49`	`HD-KOBD-II`	Korea Heavy Duty OBD-II
`50`	`CN-OROBD-IV`	China Off-Road IV OBD
`51`	`CARB ACC-II`	Light Duty ZEV, ACC-II
`52`	`MC JOBD-II`	Motorcycle, Japan OBD-II
`53`	`MC CARB OBD`	Motorcycle, California (CARB) OBD
`54`	`MC EPA OBD`	Motorcycle, Federal (EPA) OBD
`55`	`MC CARB & EPA OBD`	Motorcycle, 50-State (CARB & EPA) OBD
`56`	`HD ZEV CARB ZEP`	Heavy Duty ZEV, CARB ZEP
`57`	`CARB ACC-II & EPA TIER4`	Light Duty ZEV, CARB ACC-II and EPA Tier 4 (GTR 22)
`58`	`EPA TIER4`	Light Duty ZEV, EPA Tier 4 (GTR 22)
`59`	`EPA HD`	EPA HD OBD

Confirmed for 2011, 2017. Supported for 2013.

Transmission

Current gear `BCLASS_CURRENT_GEAR`

Service 21PID 30
Module7E1 → 7E9
Every5 s
Testing

Bits 80 to 87 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255
Unit: Number

In testing for 2005 to 2026.

Torque converter slip `BCLASS_TQ_CONV_SLIP`

Service 21PID 30
Module7E1 → 7E9
Every5 s
Testing

Bits 8 to 15 of the reply, 8 bits.

Formula: $val$
Range: 0 to 255 rpm
Unit: rpm

In testing for 2005 to 2026.

Transmission fluid temperature, variant 1 `BCLASS_ATF_T_VAR_1`

Service 21PID 30
Module7E1 → 7E9
Every5 s
Testing

Bits 88 to 95 of the reply, 8 bits.

Formula: $\frac{val \times 9}{5} - 58$
Range: -58 to 401 °F
Unit: °F

In testing for 2005 to 2026.

Transmission fluid temperature, variant 2 `BCLASS_ATF_T_VAR_2`

Service 22DID 0230
Module7E1 → 7E9
Every5 s
Testing

Bits 88 to 95 of the reply, 8 bits.

Formula: $\frac{val \times 9}{5} - 58$
Range: -58 to 401 °F
Unit: °F

In testing for 2005 to 2026.

Transmission fluid temperature, variant 3 `BCLASS_ATF_T_VAR_3`

Service 21PID 34
Module7E1 → 7E9
Every5 s
Testing

Bits 72 to 87 of the reply, 16 bits. The value is signed.

Formula: $\frac{val}{10}$
Range: -3276 to 3276 °C
Unit: °C

In testing for 2005 to 2026.

Transmission fluid temperature, variant 4 `BCLASS_ATF_T_VAR_4`

Service 22DID 0234
Module7E1 → 7E9
Every5 s
Testing

Bits 24 to 31 of the reply, 8 bits.

Formula: $val - 50$
Range: -50 to 205 °C
Unit: °C

In testing for 2005 to 2026.

Trips

Odometer `BCLASS_ODO`

Service 22DID 016B
Module7E0 → 7E8
Every30 s
Testing

Bits 288 to 303 of the reply, 16 bits.

Formula: $val \times 2$
Range: 0 to 131070 km
Unit: km

In testing for 2005 to 2026.

Parameters

Battery

Control module voltage VPWRSAE J1979Confirmed

Climate

Ambient air temperature AATSAE J1979Confirmed

Clocks

Time since engine start RUNTMSAE J1979Confirmed

Control Pedals

Accelerator pedal position D APP_DSAE J1979Confirmed

Accelerator pedal position E APP_ESAE J1979Confirmed

DTCs

Distance traveled since diagnostic trouble codes cleared CLR_DISTSAE J1979Confirmed

Distance traveled while MIL was activated MIL_DISTSAE J1979Confirmed

Malfunction indicator lamp MILSAE J1979Confirmed

Number of DTCs stored in this ECU DTC_CNTSAE J1979Confirmed

Number of warm-ups since diagnostic trouble codes cleared WARM_UPSSAE J1979Confirmed

Time run by the engine while MIL was activated MIL_TIMESAE J1979Confirmed

Status

A/C system refrigerant monitoring ACRF_ENASAE J1979Confirmed

A/C system refrigerant monitoring completed ACRFCMPLSAE J1979Confirmed

A/C system refrigerant monitoring ready ACRF_RDYSAE J1979Confirmed

Catalyst monitoring CAT_ENASAE J1979Confirmed

Catalyst monitoring completed CAT_CMPLSAE J1979Confirmed

Catalyst monitoring ready CAT_RDYSAE J1979Confirmed

Comprehensive component monitoring completed CCM_CMPLSAE J1979Confirmed

Comprehensive component monitoring ready CCM_RDYSAE J1979Confirmed

EGR system monitoring EGR_ENASAE J1979Confirmed

EGR system monitoring completed EGR_CMPLSAE J1979Confirmed

EGR system monitoring ready EGR_RDYSAE J1979Confirmed

Evaporative system monitoring EVAP_ENASAE J1979Confirmed

Evaporative system monitoring completed EVAPCMPLSAE J1979Confirmed

Evaporative system monitoring ready EVAP_RDYSAE J1979Confirmed

Fuel system monitoring completed FUEL_CMPLSAE J1979Confirmed

Fuel system monitoring ready FUEL_RDYSAE J1979Confirmed

Heated catalyst monitoring HCAT_ENASAE J1979Confirmed

Heated catalyst monitoring completed HCATCMPLSAE J1979Confirmed

Heated catalyst monitoring ready HCAT_RDYSAE J1979Confirmed

Misfire monitoring completed MIS_CMPLSAE J1979Confirmed

Misfire monitoring ready MIS_RDYSAE J1979Confirmed

Oxygen sensor heater monitoring HTR_ENASAE J1979Confirmed

Oxygen sensor heater monitoring completed HTR_CMPLSAE J1979Confirmed

Oxygen sensor heater monitoring ready HTR_RDYSAE J1979Confirmed

Oxygen sensor monitoring O2S_ENASAE J1979Confirmed

Oxygen sensor monitoring completed O2S_CMPLSAE J1979Confirmed

Oxygen sensor monitoring ready O2S_RDYSAE J1979Confirmed

Secondary air system monitoring AIR_ENASAE J1979Confirmed

Secondary air system monitoring completed AIR_CMPLSAE J1979Confirmed

Secondary air system monitoring ready AIR_RDYSAE J1979Confirmed

Support

A/C system refrigerant monitoring supported ACRF_SUPSAE J1979Confirmed

Catalyst monitoring supported CAT_SUPSAE J1979Confirmed

Comprehensive component monitoring enabled CCM_ENASAE J1979Confirmed

Comprehensive component monitoring supported CCM_SUPSAE J1979Confirmed

Compression ignition monitoring supported CIM_SUPSAE J1979Confirmed

Compression ignition monitoring supported CIM_SUP_FLAGSAE J1979Confirmed

EGR system monitoring supported EGR_SUPSAE J1979Confirmed

Evaporative system monitoring supported EVAP_SUPSAE J1979Confirmed

Fuel system monitoring enabled FUEL_ENASAE J1979Confirmed

Fuel system monitoring supported FUEL_SUPSAE J1979Confirmed

Heated catalyst monitoring supported HCAT_SUPSAE J1979Confirmed

Misfire monitoring enabled MIS_ENASAE J1979Confirmed

Misfire monitoring supported MIS_SUPSAE J1979Confirmed

Oxygen sensor heater monitoring supported HTR_SUPSAE J1979Confirmed

Oxygen sensor monitoring supported O2S_SUPSAE J1979Confirmed

Secondary air system monitoring supported AIR_SUPSAE J1979Confirmed

Engine

Absolute load value LOAD_ABSSAE J1979Confirmed

Air flow rate from mass air flow sensor MAFSAE J1979Confirmed

Barometric pressure BAROSAE J1979Confirmed

Boost air temperature BCLASS_BOOST_AIR_T

Boost pressure BCLASS_BOOST_P

Boost pressure sensor A BP_A_ACTSAE J1979Confirmed

Boost pressure sensor B BP_B_ACTSAE J1979Confirmed

Calculated engine load LOAD_PCTSAE J1979Confirmed

Catalyst temperature bank 1, sensor 1 CATEMP11SAE J1979Confirmed

Commanded boost pressure A BP_A_CMDSAE J1979Confirmed

Commanded boost pressure B BP_B_CMDSAE J1979Confirmed

Commanded equivalence ratio EQ_RATSAE J1979Confirmed

Commanded evaporative purge EVAP_PCTSAE J1979Confirmed

Commanded Throttle Actuator A Control TAC_A_CMDSAE J1979Confirmed

Control module voltage `VPWR`SAE J1979Confirmed

Ambient air temperature `AAT`SAE J1979Confirmed

Time since engine start `RUNTM`SAE J1979Confirmed

Accelerator pedal position D `APP_D`SAE J1979Confirmed

Accelerator pedal position E `APP_E`SAE J1979Confirmed

Distance traveled since diagnostic trouble codes cleared `CLR_DIST`SAE J1979Confirmed

Distance traveled while MIL was activated `MIL_DIST`SAE J1979Confirmed

Malfunction indicator lamp `MIL`SAE J1979Confirmed

Number of DTCs stored in this ECU `DTC_CNT`SAE J1979Confirmed

Number of warm-ups since diagnostic trouble codes cleared `WARM_UPS`SAE J1979Confirmed

Time run by the engine while MIL was activated `MIL_TIME`SAE J1979Confirmed

A/C system refrigerant monitoring `ACRF_ENA`SAE J1979Confirmed

A/C system refrigerant monitoring completed `ACRFCMPL`SAE J1979Confirmed

A/C system refrigerant monitoring ready `ACRF_RDY`SAE J1979Confirmed

Catalyst monitoring `CAT_ENA`SAE J1979Confirmed

Catalyst monitoring completed `CAT_CMPL`SAE J1979Confirmed

Catalyst monitoring ready `CAT_RDY`SAE J1979Confirmed

Comprehensive component monitoring completed `CCM_CMPL`SAE J1979Confirmed

Comprehensive component monitoring ready `CCM_RDY`SAE J1979Confirmed

EGR system monitoring `EGR_ENA`SAE J1979Confirmed

EGR system monitoring completed `EGR_CMPL`SAE J1979Confirmed

EGR system monitoring ready `EGR_RDY`SAE J1979Confirmed

Evaporative system monitoring `EVAP_ENA`SAE J1979Confirmed

Evaporative system monitoring completed `EVAPCMPL`SAE J1979Confirmed

Evaporative system monitoring ready `EVAP_RDY`SAE J1979Confirmed

Fuel system monitoring completed `FUEL_CMPL`SAE J1979Confirmed

Fuel system monitoring ready `FUEL_RDY`SAE J1979Confirmed

Heated catalyst monitoring `HCAT_ENA`SAE J1979Confirmed

Heated catalyst monitoring completed `HCATCMPL`SAE J1979Confirmed

Heated catalyst monitoring ready `HCAT_RDY`SAE J1979Confirmed

Misfire monitoring completed `MIS_CMPL`SAE J1979Confirmed

Misfire monitoring ready `MIS_RDY`SAE J1979Confirmed

Oxygen sensor heater monitoring `HTR_ENA`SAE J1979Confirmed

Oxygen sensor heater monitoring completed `HTR_CMPL`SAE J1979Confirmed

Oxygen sensor heater monitoring ready `HTR_RDY`SAE J1979Confirmed

Oxygen sensor monitoring `O2S_ENA`SAE J1979Confirmed

Oxygen sensor monitoring completed `O2S_CMPL`SAE J1979Confirmed

Oxygen sensor monitoring ready `O2S_RDY`SAE J1979Confirmed

Secondary air system monitoring `AIR_ENA`SAE J1979Confirmed

Secondary air system monitoring completed `AIR_CMPL`SAE J1979Confirmed

Secondary air system monitoring ready `AIR_RDY`SAE J1979Confirmed

A/C system refrigerant monitoring supported `ACRF_SUP`SAE J1979Confirmed

Catalyst monitoring supported `CAT_SUP`SAE J1979Confirmed

Comprehensive component monitoring enabled `CCM_ENA`SAE J1979Confirmed

Comprehensive component monitoring supported `CCM_SUP`SAE J1979Confirmed

Compression ignition monitoring supported `CIM_SUP`SAE J1979Confirmed

Compression ignition monitoring supported `CIM_SUP_FLAG`SAE J1979Confirmed

EGR system monitoring supported `EGR_SUP`SAE J1979Confirmed

Evaporative system monitoring supported `EVAP_SUP`SAE J1979Confirmed

Fuel system monitoring enabled `FUEL_ENA`SAE J1979Confirmed

Fuel system monitoring supported `FUEL_SUP`SAE J1979Confirmed

Heated catalyst monitoring supported `HCAT_SUP`SAE J1979Confirmed

Misfire monitoring enabled `MIS_ENA`SAE J1979Confirmed

Misfire monitoring supported `MIS_SUP`SAE J1979Confirmed

Oxygen sensor heater monitoring supported `HTR_SUP`SAE J1979Confirmed

Oxygen sensor monitoring supported `O2S_SUP`SAE J1979Confirmed

Secondary air system monitoring supported `AIR_SUP`SAE J1979Confirmed

Absolute load value `LOAD_ABS`SAE J1979Confirmed

Air flow rate from mass air flow sensor `MAF`SAE J1979Confirmed

Barometric pressure `BARO`SAE J1979Confirmed

Boost air temperature `BCLASS_BOOST_AIR_T`

Boost pressure `BCLASS_BOOST_P`

Boost pressure sensor A `BP_A_ACT`SAE J1979Confirmed

Boost pressure sensor B `BP_B_ACT`SAE J1979Confirmed

Calculated engine load `LOAD_PCT`SAE J1979Confirmed

Catalyst temperature bank 1, sensor 1 `CATEMP11`SAE J1979Confirmed

Commanded boost pressure A `BP_A_CMD`SAE J1979Confirmed

Commanded boost pressure B `BP_B_CMD`SAE J1979Confirmed

Commanded equivalence ratio `EQ_RAT`SAE J1979Confirmed

Commanded evaporative purge `EVAP_PCT`SAE J1979Confirmed

Commanded Throttle Actuator A Control `TAC_A_CMD`SAE J1979Confirmed

Commanded Throttle Actuator B Control `TAC_B_CMD`SAE J1979Confirmed

Commanded throttle actuator control `TAC_PCT`SAE J1979Confirmed

Diesel particulate filter differential pressure `BCLASS_DPF_DIFF_P`

Engine coolant temperature `ECT`SAE J1979Confirmed

Engine coolant temperature 1 `ECT_1`SAE J1979Confirmed

Engine coolant temperature 2 `ECT_2`SAE J1979Confirmed

Engine oil temperature `BCLASS_EOT`

Engine oil temperature `EOT`SAE J1979Confirmed

Engine RPM `RPM`SAE J1979Confirmed